Time Synchronisation

Many people are probably familiar with the Internet Time tab when setting their clock in Windows. This is a basic form of NTP (Network Time Protocol) called SNTP (Simple Network Time Protocol) that polls a NTP server every so often to synchronize time to. However, full NTP does a lot more, such as polling several servers to determine what is the best and most stable times source.

Creating your own NTP time server is relatively straightforward and if you are a resident of the US then the simplest way is to use a relatively cheap receiver module, set to receive the WWVB timing signal which is broadcast by NIST (National Institute of Standards and Time) at a frequency of 60 kHz.

To create your own product using the WWVB time signal, WWVB receiver modules, are readily available at low cost. When looking for a receiver module there are several points to consider:

There should be a simple interface to allow easy integration of accurate timekeeping into electronic equipment etc. The receiver should use dedicated chips designed specifically to receive the WWVB (USA) time signal. The advantage of these over other solutions is that the modules include the necessary support electronics, tuned crystals, etc and are preassembled, tested and are usually in miniature form.

When combined with a suitable Antenna the receiver module acts as a complete time code receiver, providing a serial digital data output stream for external decoding.

Once assembled and tested so the module is receiving a signal it can then be connected to your computer or server.

Once connected the time server should be configured using the registry editor. Simply follow these steps:

Locate the following subkey: HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesW32TimeParametersType
In the right pane, right-click Type then click Modify, in edit Value type NTP in the Value data box then click OK.

Locate the following subkey: HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesW32TimeConfigAnnounceFlags.

In the right pane, right-click AnnounceFlags and click Modify. The ‘AnnounceFlags’ registry entry indicates whether the server is a trusted time reference, 5 indicates a trusted source so in the Edit DWORD Value box, under Value Data, type 5, then click OK.

To enable the Network Time Protocol; NTPserver, locate and click: HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesW32TimeTimeProvidersNtpServer

In the right pane, right-click Enabled, then click Modify. In the Edit DWord Value box, type 1 under Value data, then click OK.

Now go back and click on: HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesW32TimeParametersNtpServer

In the right pane, right-click NtpServer, then Modify, in the Edit DWORD Value under Value Data type In the right pane, right-click NtpServer, then Modify, in the Edit DWORD Value under Value Data type the Domain Name System (DNS), each DNS must be unique and you must append 0×1 to the end of each DNS name otherwise changes will not take effect.

Now click Ok then locate and click the following: HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesW32TimeTimeProvidersNtpClientSpecialPollInterval

In the right pane, right-click SpecialPollInterval, then click Modify. In the Edit DWORD Value box, under Value Data, type the number of seconds you want for each poll, ie 900 will poll every 15 minutes, then click OK.

To configure the time correction settings, locate: HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesW32Timeconfig

In the right pane, right-click MaxPosPhaseCorrection, then Modify, in the Edit DWORD Value box, under Base, click Decimal, under Value Data, type a time in seconds such as 3600 (an hour) then click OK.

Now go back and click: HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesW32Timeconfig In the right pane, right-click MaxNegPhaseCorrection, then Modify.

In the Edit DWORD box under base, click Decimal, under value data type the time in seconds you want to poll such as 3600 (polls in one hour) Exit Registry Editor

Now, to restart windows time service, click Start, Run (or alternatively use the command prompt facility) and type:

net stop w32time && net start w32time. And that’s it your time server should be now up and running.

Computer time synchronisation is highly important in modern computer networks, precision and time synchronization is critical in many applications, particularly time sensitive transactions. Just imagine buying an airline seat only to be told at the airport that the ticket was sold twice because it was purchased afterwards on a computer that had a slower clock!

Modern computers do have internal clocks called Real Time Clock chips (RTC) that provide time and date information. These chips are battery backed so that even during power outages, they can maintain time but personal computers are not designed to be perfect clocks. Their design has been optimized for mass production and low-cost rather than maintaining accurate time.

For many applications, this is can be quite adequate, although, quite often machines need time to be synchronised with other PC’s on a network and when computers are out of sync with each other problems can arise such as sharing network files or in some environments even fraud!

Microsoft Windows (2000 and above) has a time synchronisation utility built into the operating system called Windows Time (w32time.exe) which can be configured to operate as a network time server. It can be configured to both synchronise a network using the internal clock or an external time source.

Note: Microsoft strongly recommends that you configure a time server with a hardware source rather than from the internet where there is no authentication.

To configure Windows Time service to use the internal hardware clock, first check that w32time is located in the system services list in the registry, to check:
Click Start, Run then type regedit then click ok.
Locate and then click the following registry entry:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time

It is highly recommended that you back up the registry as serious problems may occur if you modify the registry incorrectly, modifications to the registry are done at your own risk.

Note: the following instructions are based on Windows 2000 other versions of Windows may differ.

To begin configuration for an internal clock, click on the following subkey:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\Parameters
In the right pane, right-click ReliableTimeSource, then click Modify.
In Edit DWORD Value, type 1 in the Value Data box, then click OK
Exit Registry Editor

To restart the Windows Time Service click Start, Run (or alternatively use the Command Prompt facility).
Type: net stop w32time && net start w32time
Then press enter.

To reset the local computers’ time, type the following on all computers except for the time server which must not be synchronised with itself:
w32tm –s

To configure the Windows Time service to use an external time source, click Start, Run and type regedit then click OK.

Locate the following subkey:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\Parameters
In the right pane, right-click Type then click Modify, in edit Value type NTP in the Value data box then click OK.

Now in the right pane, right click ReliableTimeSource, then click Modify.
In the Edit DWORD Value box, under Value Data, type 0, then click OK.

Right-click NtpServer in the right pane then click Modify.
In Edit Value, type the Domain Name System (DNS), each DNS must be unique.
Now click Ok.

For Windows 2000 Service Pack 4 only, set the time correction settings to do this locate:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\Parameters
In the right pane, right-click MaxAllowedClockErrInSecs, then Modify in the Edit DWORD Value box, , type a time in seconds max number of seconds difference between the local clock and the time received from the NTP server in order to be considered a valid new time.
Click OK.

To set the poll intervals locate:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\Parameters
In the right pane, right-click Period, then click Modify.
In the Edit DWORD Value box, under Value Data, type 24 then OK
Exit Registry Editor

Click Start, then Run then type the following and press Enter:
Net stop w32time && net start w32time

To reset the local computers’ time, type the following on all computers except for the time server which must not be synchronised with itself:

Network Time Protocol (NTP) is an Internet protocol used for the transfer of accurate time, providing time information along so that a precise time can be obtained

To enable the Network Time Protocol; NTPserver, locate and click:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\TimeProviders\NtpServer\
In the right pane, right-click Enabled, then click Modify.
In the Edit DWord Value box, type 1 under Value data, then click OK.

Now go back and click on
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\Parameters\NtpServer
In the right pane, right-click NtpServer, then Modify, in the Edit DWORD Value under Value Data type In the right pane, right-click NtpServer, then Modify, in the Edit DWORD Value under Value Data type the Domain Name System (DNS), each DNS must be unique and you must append 0×1 to the end of each DNS name otherwise changes will not take effect.
Now click Ok.

Locate and click the following
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\TimeProviders\NtpClient\SpecialPollInterval
In the right pane, right-click SpecialPollInterval, then click Modify.
In the Edit DWORD Value box, under Value Data, type the number of seconds you want for each poll, ie 900 will poll every 15 minutes, then click OK.

To configure the time correction settings, locate:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\config
In the right pane, right-click MaxPosPhaseCorrection, then Modify, in the Edit DWORD Value box, under Base, click Decimal, under Value Data, type a time in seconds such as 3600 (an hour) then click OK.

Now go back and click:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\config
In the right pane, right-click MaxNegPhaseCorrection, then Modify.
In the Edit DWORD box under base, click Decimal, under value data type the time in seconds you want to poll such as 3600 (polls in one hour)

Exit Registry Editor
Now to restart windows time service, click Start, Run (or alternatively use the command prompt facility) and type:
net stop w32time && net start w32time

And on each computer, other than the time server, type:
W32tm/ -s

And that’s it your time server should be now up and running.

This article explains how to configure Windows 2003 to run as a Network Time Server.

Time synchronisation in modern computer networks is essential, all computers need to know the time as many applications, from sending an email to storing information are reliant on the PC knowing when the event took place.

Microsoft Windows Server from 2000 onwards has a time synchronisation utility built into the operating system called Windows Time (w32time.exe) which can be configured to operate as a network time server.

Windows 2003 Server can easily set the system clock to use UTC (Coordinated Universal Time, the World’s time standard) by accessing an Internet source (either: time.windows.com or time.nist.gov). To achieve this, a user merely has to double click the clock on their desktop and adjust the settings in the Internet Time tab.

It must be noted however, that Microsoft and other operating system manufacturers strongly advise that external timing references should be used as Internet sources can’t be authenticated.

To configure the Windows Time service to use an external time source, click Start, Run and type regedit then click OK.
Locate the following subkey:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\Parameters\Type

In the right pane, right-click Type then click Modify, in edit Value type NTP in the Value data box then click OK.

Locate the following subkey:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\Config\AnnounceFlags.

In the right pane, right-click AnnounceFlags and click Modify. The ‘AnnounceFlags’ registry entry indicates whether the server is a trusted time reference, 5 indicates a trusted source so in the Edit DWORD Value box, under Value Data, type 5, then click OK.

Network Time Protocol (NTP) is an Internet protocol used for the transfer of accurate time, providing time information along so that a precise time can be obtained.

To enable the Network Time Protocol; NTPserver, locate and click:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\TimeProviders\NtpServer\

In the right pane, right-click Enabled, then click Modify.

In the Edit DWord Value box, type 1 under Value data, then click OK.

Now go back and click on

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\Parameters\NtpServer

In the right pane, right-click NtpServer, then Modify, in the Edit DWORD Value under Value Data type In the right pane, right-click NtpServer, then Modify, in the Edit DWORD Value under Value Data type the Domain Name System (DNS), each DNS must be unique and you must append 0×1 to the end of each DNS name otherwise changes will not take effect.

Now click Ok.

Locate and click the following

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\TimeProviders\NtpClient\SpecialPollInterval

In the right pane, right-click SpecialPollInterval, then click Modify.

In the Edit DWORD Value box, under Value Data, type the number of seconds you want for each poll, ie 900 will poll every 15 minutes, then click OK.

To configure the time correction settings, locate:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\config

In the right pane, right-click MaxPosPhaseCorrection, then Modify, in the Edit DWORD Value box, under Base, click Decimal, under Value Data, type a time in seconds such as 3600 (an hour) then click OK.

Now go back and click:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\config

In the right pane, right-click MaxNegPhaseCorrection, then Modify.

In the Edit DWORD box under base, click Decimal, under value data type the time in seconds you want to poll such as 3600 (polls in one hour)

Exit Registry Editor

Now, to restart windows time service, click Start, Run (or alternatively use the command prompt facility) and type:

net stop w32time && net start w32time

And that’s it your time server should be now up and running.

Network Time Protocol has been developed to keep computers synchronized. All computers are prone to drift and accurate timing is essential for many time critical applications.

A version of NTP is installed on most versions of Windows (although a stripped down version called SNTP –Simplified NTP- is in older versions) and Linux but is free to download from NTP.org.

When synchronising a a network it is preferable to use a dedicated NTP server that receives a timing source from an atomic clock either via specialist radio transmissions or the GPS network. However, many Internet time references are available, some more reliable than others, although it must be noted Internet based time sources can’t be authenticated by NTP, leaving your computer vulnerable to threats.

NTP is hierarchical and arranged into stratum. Stratum 0 is timing reference, while stratum 1 is a server connected to a stratum 0 timing source and a stratum 2 is a computer (or device) attached to a stratum 1 server.

The Basic configuration of NTP is done using the /etc/ntp.conf file you have to edit it and place the IP address of stratum 1 and stratum 2 servers. Here is an example of a basic NTP.conf file:

server xxx.yyy.zzz.aaa prefer (time server address such as time.windows.com)

server 123.123.1.0

server 122.123.1.0 stratum 3

Driftfile /etc/ntp/drift

The most basic NTP.conf file will list 2 servers, one that it wishes to synchronise too and an IP address for itself. It is good housekeeping to have more than one server for reference in case one goes down.

A server with the tag ‘prefer’ is used for a trusted source ensuring NTP will always use that server when possible. The IP address will be used in case of problems when NTP will synchonise with itself is. The drift file is where NTP builds a record of the system clock’s drift rate and automatically adjusts for it.

NTP will adjust your system time but only slowly. NTP will await at least ten packets of information before trusting the time source. To test NTP simply change your system clock by half an hour at the end of the day and the time in the morning should be correct.

A time server is an essential piece of equipment responsible for ensuring all devices on a computer network are running the same time. Most time servers are dedicated devices that receive a time signal, normally UTC (Coordinated Universal Time), and distribute it to all devices on a network.

Most time servers use the Internet protocol NTP (Network Time Protocol) to synchronise all devices and are often referred to as NTP servers. NTP distributes a single time source throughout the network which is normally a UTC source (Coordinated Universal Time).

There are several places a time server can receive a time signal from. The internet is an obvious source for many although online time sources are not very accurate, can be too far away to give any useful precision, and more importantly are not secure being as they are external to the firewall.

As a dedicated time server is an external device they are extremely secure and impossible for malicious users to tamper with. Dedicated time server can receive a time signal from two sources the GPS network (Global Positioning System) , a highly accurate method and available everywhere on the globe with a good view of the sky; or the specialist long wave radio transmissions broadcast by national physics laboratories.

In Europe the two main radio transmissions are the UK’s MSF signal broadcast by NPL (National Physical Laboratory) in Cumbria, England and the German DCF-77 broadcast near Frankfurt.

These long wave signals are also highly accurate and can be picked up in most neighbouring countries too. The USA has a similar system called WWVB,  transmitted by the National Institute for Standards and Technology (NIST) from Boulder, Colorado.

Network Time Protocol has been developed to keep computers synchronized. All computers are prone to drift and accurate timing is essential for many time critical applications.

A version of NTP is installed on most versions of Windows (although a stripped down version called SNTP – Simplified NTP – is in older versions) and Linux but is free to download from NTP.org.

When synchronising a a network it is preferable to use a dedicated NTP server that receives a timing source from an atomic clock either via specialist radio transmissions or the GPS network. However, many Internet time references are available, some more reliable than others, although it must be noted Internet based time sources can’t be authenticated by NTP, leaving your computer vulnerable to threats.

NTP is hierarchical and arranged into stratum. Stratum 0 is timing reference, while stratum 1 is a server connected to a stratum 0 timing source and a stratum 2 is a computer (or device) attached to a stratum 1 server.

The Basic configuration of NTP is done using the /etc/ntp.conf file you have to edit it and place the IP address of stratum 1 and stratum 2 servers. Here is an example of a basic NTP.conf file:

server xxx.yyy.zzz.aaa prefer (time server address such as time.windows.com)

server 123.123.1.0

server 122.123.1.0 stratum 3

Driftfile /etc/ntp/drift

The most basic NTP.conf file will list 2 servers, one that it wishes to synchronise too and an IP address for itself. It is good housekeeping to have more than one server for reference in case one goes down.

A server with the tag ‘prefer’ is used for a trusted source ensuring NTP will always use that server when possible. The IP address will be used in case of problems when NTP will synchonise with itself is. The drift file is where NTP builds a record of the system clock’s drift rate and automatically adjusts for it.

NTP will adjust your system time but only slowly. NTP will await at least ten packets of information before trusting the time source. To test NTP simply change your system clock by half an hour at the end of the day and the time in the morning should be correct.

All versions of Windows Server since 2000 have included a time synchronization facility, called Windows Time Service (w32time.exe), built into the operating system. This can be configured to operate as a network time server synchronizing all machines to a specific time source.

Windows Time Service uses a version of NTP (Network Time Protocol), normally a simplified version, of the Internet protocol which is designed to synchronise machines on a network, NTP is also the standard for which most computer networks across the global use to synchronise with.

Choosing the correct time source is vitally important. Most networks are synchronized to UTC (Coordinated Universal Time) source. UTC is a global standardized time based on atomic clocks which are the most accurate time sources.

UTC can be obtained over the Internet from such places as time.nist.gov (us Naval Observatory) or time.windows.com (Microsoft) but it must be noted that internet time sources can not be authenticated which can leave a system open to abuse and Microsoft and others advise using an external hardware source as a reference clock such as a specialized network time server.

Network time servers receive their time source from either a specialist radio transmission from national physics laboratories which broadcast UTC time taken from an atomic clock source or by the GPS network which also relays UTC as a consequence of needing it to pin point locations.

NTP can maintain time over the public Internet to within 1/100th of a second (10 milliseconds) and can perform even better over LANs.

To configure Windows Time Service to use an external time source simply follow these instructions.

Locate the registry subkey.
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\Parameters
Right click type then Modify the Value by inserting NTP in the Value Data box.
Right click ReliableTimeSource, then Modify the Edit DWORD Value box, by inserting 0 (zero).
Right-click NtpServer then Modify the Edit Value by typing the Domain Name System (DNS), (note each DNS must be unique).

Now locate the original subkey and right-click Period Modify the Edit DWORD Value box with the poll interval (how often a NTP server polls the time), under Value Data (recommended 24)

Run the following command line, Net stop w32time && net start w32time.
Now enable NTP by locating the subkey,
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\TimeProviders\NtpServer\
Right click Enabled and modify the Value data box by typing 1.

Right Click SpecialPollInterval in the right pain of the subkey
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\TimeProviders\NtpClient\SpecialPollInterval.
Edit the DWORD value box the time you want for each poll (900 will poll every 15 minutes)

Locate HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\config

To configure the time correction settings right click MaxPosPhaseCorrection, then modify the DWORD Value box with a time in seconds such (select decimal under base first, 3600 = one hour)

Now do the same for MaxNegPhaseCorrection the restart windows time service by running (or alternatively use the command prompt facility) net stop w32time && net start w32time.

To synchronise each machine simply type W32tm/ -s in the command prompt and the time server should now be working correctly (note it may take several polls before the correct time is displayed).

Microsoft Windows XP has a time synchronisation utility built into the operating system called Windows Time (w32time.exe) which can be configured to operate as a network time server. It can be configured to both synchronise a network using the internal clock or an external time source.

NTP (Network Time Protocol) is a protocol already installed on Windows XP and Windows Time uses it to keep machines synchronised to the single time source. There are several timing sources available on the Internet but Microsoft and others strongly recommend that you configure a time server with a hardware source rather than from the Internet where there is no authentication.

Specialist NTP time servers are available that can receive a reliable time source via the GPS signal or specialist radio transmissions that get their time from atomic clocks.

If you wish to configure Windows XP to operate as a time server then first thing is to locate the Windows Time subkey. To do this:

Run Regedit (Click start/run/then type REGEDIT/and click enter.

Note: editing your system registry can cause problems with your system. It is advisable to back up your system before editing the registry.

Now locate the following subkey:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\parameters\

Right click the right-hand side and click Modify. In the Edit Value box, under Value Data, type NTP and then click OK.

Now go to the Config folder and right-click AnnounceFlags, Modify and in the Edit DWORD Value box, under Value Data, type 5, and then click OK.

Locate this subkey:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\TimeProviders\NtpClient\

Right-click in the right-side window and Modify. Edit the DWORD value box and type the number of seconds you want for each poll under Value data, i.e.: 900 will equal 15 minutes. The poll field represents the polling interval between NTP poll packets.

To enable the NTP server locate the subkey:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\TimeProviders\NtpServer\

Right click enabled (in the right-hand window) then Modify. Edit the DWORD Value and type 1. Right-click NtpServer, then Modify and in the Edit DWORD Value under Value Data type Peers, then click OK.

Locate: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\config

In the right pane, right-click MaxPosPhaseCorrection, then Modify, in the Edit DWORD Value box, under Base, click Decimal, under Value Data, type a time in seconds such as 3600 (an hour) then click OK. This adjusts the connection settings.

Now go back and click:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\config

In the right pane, right-click MaxNegPhaseCorrection, then Modify.

In the Edit DWORD box under base, click Decimal, under value data type the time in seconds you want to poll such as 3600 (an hour).

Exit Registry then restart windows time service by clicking Start/Run then typing:
net stop w32time && net start w32time.
on each computer, other than the domain controller, type: W32tm/resync/rediscover.
The time server should be now up and running.

Time synchronisation in modern computer networks is essential, all computers need to know the time as many applications, from sending an email to storing information are reliant on the PC knowing when the event took place.

Microsoft Windows Server from 2000 onwards has a time synchronisation utility built into the operating system called Windows Time (w32time.exe) which can be configured to operate as a network time server.

Windows Server 2008 can easily set the system clock to use UTC (Coordinated Universal Time, the World’s time standard) by accessing an Internet source (either: time.windows.com or time.nist.gov).

To achieve this, a user merely has to double click the clock on their desktop and adjust the settings in the Internet Time tab.

It must be noted however, that Microsoft and other operating system manufacturers strongly advise that external timing references should be used as Internet sources can’t be authenticated.

To configure the Windows Time service to use an external time source, click Start, Run and type regedit then click OK.

Locate the following subkey:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\Parameters\Type
In the right pane, right-click Type then click Modify, in edit Value type NTP in the Value data box then click OK.

Locate the following subkey:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\Config\AnnounceFlags.
In the right pane, right-click AnnounceFlags and click Modify. The ‘AnnounceFlags’ registry entry indicates whether the server is a trusted time reference, 5 indicates a trusted source so in the Edit DWORD Value box, under Value Data, type 5, then click OK.

Network Time Protocol (NTP) is an Internet protocol used for the transfer of accurate time, providing time information along so that a precise time can be obtained
To enable the Network Time Protocol; NTPserver, locate and click:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\TimeProviders\NtpServer\
In the right pane, right-click Enabled, then click Modify.

In the Edit DWord Value box, type 1 under Value data, then click OK.

Now go back and click on
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\Parameters\NtpServer
In the right pane, right-click NtpServer, then Modify, in the Edit DWORD Value under Value Data type the Domain Name System (DNS), each DNS must be unique and you must append 0×1 to the end of each DNS name otherwise changes will not take effect.

Now click Ok.

Locate and click the following
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\TimeProviders\NtpClient\SpecialPollInterval
In the right pane, right-click SpecialPollInterval, then click Modify.

In the Edit DWORD Value box, under Value Data, type the number of seconds you want for each poll, ie 900 will poll every 15 minutes, then click OK.
To configure the time correction settings, locate:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\config
In the right pane, right-click MaxPosPhaseCorrection, then Modify, in the Edit DWORD Value box, under Base, click Decimal, under Value Data, type a time in seconds such as 3600 (an hour) then click OK.
Now go back and click:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\config
In the right pane, right-click MaxNegPhaseCorrection, then Modify.

In the Edit DWORD box under base, click Decimal, under value data type the time in seconds you want to poll such as 3600 (polls in one hour)
Exit Registry Editor
Now, to restart windows time service, click Start, Run (or alternatively use the command prompt facility) and type:

net stop w32time && net start w32time
And that’s it your time server should be now up and running.

Nearly all a computers activity involves time whether logging a timestamp for when a network was accessed to sending an email, knowing the time is crucial for computer applications.

All computers have an on-board clock that provides time and date information. These Real Time Clock (RTC) chips are battery backed so that even when off they can maintain time, however these RTC chips are mass produced and cannot maintain accurate time and tend to drift.

For many applications this can be quite adequate, however if a computer is on a network and needs to talk to other machines, failing to be synchonised to the correct time can mean many time-sensitive transactions can not be completed and can even leave the network open to security threats.

All versions of Windows Server since 2000 have included a time synchronization facility, called Windows Time Service (w32time.exe), built into the operating system. This can be configured to operate as a network time server synchronizing all machines to a specific time source.

Windows Time Service uses a version of NTP (Network Time Protocol), normally a simplified version, of the Internet protocol which is designed to synchronise machines on a network, NTP is also the standard for which most computer networks across the global use to synchronise with.

Choosing the correct time source is vitally important. Most networks are synchronized to UTC (Coordinated Universal Time) source. UTC is a global standardized time based on atomic clocks which are the most accurate time sources.

UTC can be obtained over the Internet from such places as time.nist.gov (us Naval Observatory) or time.windows.com (Microsoft) but it must be noted that internet time sources can not be authenticated which can leave a system open to abuse and Microsoft and others advise using an external hardware source as a reference clock such as a specialized NTP server.

NTP servers receive their time source from either a specialist radio transmission from national physics laboratories which broadcast UTC time taken from an atomic clock source or by the GPS network which also relays UTC as a consequence of needing it to pin point locations.

NTP can maintain time over the public Internet to within 1/100th of a second (10 milliseconds) and can perform even better over LANs.