Time Synchronisation

Accurate time using Atomic Clocks is available across North America using the WWVB Atomic Clock time signal transmitted from Fort Collins, Colorado; it provides the ability to synchronize the time on computers and other electrical equipment.

The North American WWVB signal is operated by NIST – the National Institute of Standards and Technology. WWVB has high transmitter power (50,000 watts), a very efficient antenna and an extremely low frequency (60,000 Hz). For comparison, a typical AM radio station broadcasts at a frequency of 1,000,000 Hz. The combination of high power and low frequency gives the radio waves from WWVB a lot of bounce, and this single station can therefore cover the entire continental United States plus much of Canada and Central America.

The time codes are sent from WWVB using one of the simplest systems possible, and at a very low data rate of one bit per second. The 60,000 Hz signal is always transmitted, but every second it is significantly reduced in power for a period of 0.2, 0.5 or 0.8 seconds: 0.2 seconds of reduced power means a binary zero 0.5 seconds of reduced power is a binary one. 0.8 seconds of reduced power is a separator. The time code is sent in BCD (Binary Coded Decimal) and indicates minutes, hours, day of the year and year, along with information about daylight savings time and leap years.

The time is transmitted using 53 bits and 7 separators, and therefore takes 60 seconds to transmit. A clock or watch can contain an extremely small and relatively simple antenna and receiver to decode the information in the signal and set the clock’s time accurately. All that you have to do is set the time zone, and the atomic clock will display the correct time.

Dedicated NTP time servers that are tuned to receive the WWVB time signal are available. These devices connect o a computer network like any other server only these receive the timing signal and distribute it to other machines on the network using NTP (Network Time Protocol).

UTC – Coordinated Universal Time (from the French: Universel Temps Coordonné) is a global timescale based on Greenwich Meantime (GMT – from the Greenwich Meridian line where the sun is above at 12 noon). But accounts for the natural slowing of the Earth’s rotation. It is used globally in commerce, computer networks via a NTP server, air-traffic control and the World’s stock exchanges to name but a few of its applications.

UTC is really the only solution for time synchronisation needs. While it is just as possible to synchronise a computer network with an NTP server to a time other than UTC it is pointless. As UTC is utilised by computer networks all across the globe by using a UTC time source that means your network can synchronise with every other network in the world that is synchronised to UTC.

UTC is most commonly received from across the Internet, however, this can only be recommended for small network users where either accuracy or security is an issue. An Internet based UTC source is external to the firewall so will leave a potential hole for malicious users to exploit.

Two secure methods of receiving UTC are commonly available. These are either the GPS network (Global Positioning System) or specialist radio transmission broadcast on long wave from several of the world’s national physics laboratories. The two methods have both advantages and disadvantages which need to be ascertained before a method is selected.

A radio transmission such as the UK’s MSF, the German DCF-77 or the USA’s WWVB signal are vulnerable to local topography although many of these signals can be picked up indoors. Whilst not every country transmits a UTC radio signal around the neighbouring countries that do it is possible to still receive it.

GPS on the other hand is available literally anywhere on the globe. The signal comes directly from above and as long as the antenna has a good clear view of the sky it can be received anywhere. However, as the antenna has to be on a roof looking up this can have logistical problems (particularly for very tall buildings).

Specialist dedicated network time servers are available that can actually receive both methods of UTC but whether using GPS or a radio transmissions synchronisation of a network to within a few milliseconds is possible.

NTP – Network Time Protocol

SNTP – Simple Network Time Protocol

GPS – Global Positioning System

UTC – Coordinated Universal Time

MSF – Radio Time Signal for United Kingdom

WWVB – Radio Time Signal for American

DCF – Radio Time Signal for Germany

LAN – Local Area Network

UDP – User Datagram Protocol

TCP – Transmission Control Protocol

IP – Internet Protocol

TDF – Radio Time Signal for France

CHU – Radio Time Signal for Canada

JJY – Radio Time Signal for Japan

HBG – Radio Time Signal for Switzerland

USB – Universal Serial Bus

RTC – Real Time Clock

AM – Amplitude Modulation

APM – Automatic Power Management

DES – Data Encryption Standard

ESD – Electrostatic Discharge

FM – Frequency Modulation

IETF – Internet Engineering Task Force

IRIG – Inter-Range Instrumentation Group

MD5 – Message Digest

PPM – Part Per Million

PPS – Pulse Per Second

RFC – Request For Comments

SA – Selective Availability

TAI – International Atomic Time

SI – International System of Units

The NTP server is an essential network tool. Whilst other protocols do exist, NTP is by far the standard time synchronisation protocol and is utilised in the majority of time servers.

A NTP server is reliant on a single time source it is this time reference that it uses to distribute amongst the network and synchronise to. This timing reference tends to be a UTC time source (coordinated universal time) which is a global time source based on the time told by atomic clocks.

There are only two viable options for receiving a UTC timing source. Although the Internet can be used, the signal can’t be authenticated this is a security measure used by NTP to ensure the reference is what it says it is. Also by using an Internet time source a hole must be left open in the network firewall to allow for communication to the server, this has its own security risks.

The only two secure methods for receiving a UTC time signal is to either use the GPS network or national time and frequency transmissions that are broadcast by several countries’ national physics laboratories.

In selecting a timing source for a NTP server, location is the key consideration. The national time and frequency transmissions are not available in every country. Whilst the USA, UK, Germany, France, Japan and Finland have a signal there are many countries that do not. Furthermore being a long wave radio transmission it can easily be blocked by local topography, although the radio aerial can pick op a signal indoors which is something a GPS NTP server can’t do.

GPS antennas have to be situated on a roof. This can have logistical problems if the server room is in the basement of a high storey building but on the plus inside the GPS signal can be received literally anywhere in the world.

The NTP time server (Network Time Protocol) is an essential tool for keeping networks synchronised. Without adequate synchronization, computer networks can be left vulnerable to security threats, data loss, fraud and may find it impossible to interact with other networks across the globe.

Computer networks are normally synchronised to the global timescale UTC (Coordinated Universal Time) enabling them to communicate efficiently with other networks also running UTC.

Whilst UTC time sources are available across the Internet these are not secure (being outside the firewall) and many are either too far away to provide adequate precision or are too inaccurate to begin with.

The most secure methods of receiving a UTC time source are to use a dedicated NTP Time Server. These devices can receive a secure and accurate time signal either the GPS network (Global Positioning System) available anywhere across the globe with a good view of the sky or through specialist radio transmission broadcast by national physics laboratories.

In the US the National Institute for Standards and Time (NIST) broadcast a time signal from near Fort Collins, Colorado. The signal, known as WWVB can be received all over North America (including many parts of Canada) and provides an accurate and secure method of receiving UTC.

As the signal is derived from atomic clocks situated at the Fort Collins site, WWVB is a highly accurate method of synchronising time and is also secure as a dedicated NTP time server acts as an external source.

Synchronising a network is often considered a headache by network administrators who fear that getting it wrong can lead to disastrous results and while there is no deny that a lack of synchronisation can cause unforeseen problems particularly with time sensitive transactions and security, perfect synchronisation is simple if these steps are followed:

1. Use a dedicated NTP server. The NTP server is a device that receives a single time source then distributes it amongst a network of computers using the protocol NTP (Network Time Protocol) one of the oldest Internet based protocols and by far the most widely used time synchronisation software. NTP is often packaged with modern operating systems such as Windows or Linux although there is no substitute for a dedicated NTP device.

2. Always use a UTC time source (Coordinated Universal Time). UTC is based on GMT (Greenwich Meantime) and International Atomic Time (TAI) and is highly accurate. UTC is used by computer networks all over the world ensuring that commerce and trade are all using the same timescale.

3. Use a secure an accurate time signal. Whilst time signals are available all over the Internet they are unpredictable in their accuracy and while some may offer decent enough precision an Internet time server is outside a networks firewall which if left open to receive a timecode will cause vulnerabilities in the security of the network. Either GPS (global positioning system) or a dedicated radio signal such as those transmitted by national physics laboratories (such as MSF – UK, WWVB – USA, DCF –Germany) offer secure and reliable methods of receiving a secure and accurate time signal.

4. Organise a network into stratum, levels. Strata ensure that the NTP server is not inundated with time requests and that the network bandwidth doesn’t become congested. A stratum tree is organised by a few select machines being stratum 2 devices in that they receive a time signal from the NTP server (stratum 1 device) these in turn distribute the time to other devices (stratum 3) and so on.

5. Ensure all machines are utilising UTC and the NTP server tree. A common error in time synchronisation is to not ensure all machines are properly synchronised, just one machine running inaccurate time can have unforeseen consequences.

A time server is an integral part of any network system. It ensures all machines on a network or keeping the exact same time, failure to do so could lead to all sorts of problems, particularly with time sensitive transactions.

Most computer networks are synchronised to UTC (coordinated Universal Time). UTC is a global time scale and used throughout the world. It is also highly precise as it is based on the time told by atomic clocks.

Atomic clocks are ideal sources of time as they do not drift whilst the standard electrical oscillators on our PC clocks can drift by a second every week. This drift can cause untold problems which is why most networks are synchronised to a time server that receives a time signal from an atomic clock.

Atomic clock time signals can be received from a myriad of sources. The Internet is an obvious choice but unless security and precision is not an issue then it is not recommended for any commercial networks as using an Internet times source can leave a system open to security threats.

For security and accuracy there are two options to synchronise to an atomic clock. One is to use a GPS time server that receives the time-code from the GPS system. The other method is to use a time server that can receive the long wave radio transmissions broadcast from several national physics laboratories.

Accurate time using Atomic Clocks is available across North America using the WWVB Atomic Clock time signal transmitted from Fort Collins, Colorado; it provides the ability to synchronize the time on computers and other electrical equipment.

The North American WWVB signal is operated by NIST – the National Institute of Standards and Technology. WWVB has high transmitter power (50,000 watts), a very efficient antenna and an extremely low frequency (60,000 Hz). For comparison, a typical AM radio station broadcasts at a frequency of 1,000,000 Hz. The combination of high power and low frequency gives the radio waves from WWVB a lot of bounce, and this single station can therefore cover the entire continental United States plus much of Canada and Central America.

The time codes are sent from WWVB using one of the simplest systems possible, and at a very low data rate of one bit per second. The 60,000 Hz signal is always transmitted, but every second it is significantly reduced in power for a period of 0.2, 0.5 or 0.8 seconds: • 0.2 seconds of reduced power means a binary zero • 0.5 seconds of reduced power is a binary one. • 0.8 seconds of reduced power is a separator. The time code is sent in BCD (Binary Coded Decimal) and indicates minutes, hours, day of the year and year, along with information about daylight savings time and leap years.

The time is transmitted using 53 bits and 7 separators, and therefore takes 60 seconds to transmit. A clock or watch can contain an extremely small and relatively simple antenna and receiver to decode the information in the signal and set the clock’s time accurately. All that you have to do is set the time zone, and the atomic clock will display the correct time.

Dedicated NTP time servers that are tuned to receive the WWVB time signal are available. These devices connect o a computer network like any other server only these receive the timing signal and distribute it to other machines on the network using NTP (Network Time Protocol).

The WWVB time signal is a dedicated radio broadcast providing an accurate and reliable source of United States civil time, based on the global time scale UTC (Coordinated Universal Time), the WWVB signal is broadcast and maintained by the United States’ NIST laboratory (National Institute for Standards and Time).

The WWVB time signal can be utilised by anyone requiring accurate timing information although its main use is as a source of UTC time for administrators synchronising a computer network with a radio clock. Radio clocks are really another term for a network time server that utilises a radio transmission as a timing source.

Most radio based network time servers use NTP (Network Time Protocol) to distribute the timing information throughout the network.

The WWVB signal is broadcast from Fort Collins, Colorado. It is available 24 hours a day across most of the USA and Canada, although the signal is vulnerable to interference and local topography. Users of the WWVB service receive predominantly a ‘ground wave’ signal. However, there is also a residual ‘sky wave’ which is reflected off the ionosphere and is much stronger at night; this can result in a total received signal that is either stronger or weaker.

The WWVB signal is carried on a frequency of 60 kHz (to within 2 parts in 1012) and is controlled by a caesium atomic clock based at NIST

The signal’s field strength exceeds 100 µV/m (microvolts a meter) at a distance of 1000 km from Colorado – covering much of the USA.

The WWVB signal is in the form of a simple binary code containing time and date information The WWVB  time and date code includes the following information: year, month, day of month,  day of week,  hour, minute, Summer Time (in effect or imminent).